1.Zkladn vypotan parametry bez zmny dlky a prmru motoru 

ADJUSTABLE-SPEED PERMANENT MAGNET SYNCHRONOUS MOTOR DESIGN

                      File: Setup1.res


     GENERAL DATA

Rated Output Power (kW):	160
Rated Voltage (V):	690
Number of Poles:	8
Frequency (Hz):	166.667
Frictional Loss (W):	500
Windage Loss (W):	1115.2
Rotor Position:	Inner
Type of Circuit:	Y3
Type of Source:	Sine
Domain:	Time
Operating Temperature (C):	75


     STATOR DATA 

Number of Stator Slots:	48
Outer Diameter of Stator (mm):  	474.3
Inner Diameter of Stator (mm):  	323.2

Type of Stator Slot:	2
Stator Slot	
            hs0 (mm):  	1
            hs1 (mm):  	2
            hs2 (mm):  	32
            bs0 (mm):  	3
            bs1 (mm):  	10.3
            bs2 (mm):  	14.4
Top Tooth Width (mm):  	11.2519
Bottom Tooth Width (mm):  	11.3464
Skew Width (Number of Slots):	0

Length of Stator Core (mm):  	125.7
Stacking Factor of Stator Core:	0.95
Type of Steel:	M800-50A
Slot Insulation Thickness (mm):  	0
Layer Insulation Thickness (mm):  	0
End Length Adjustment (mm):  	0
Number of Parallel Branches:	2
Number of Conductors per Slot:	28
Type of Coils:	21
Average Coil Pitch:	3
Number of Wires per Conductor:	1
Wire Diameter (mm):  	3.459
Wire Wrap Thickness (mm):  	0.05
Slot Area (mm^2):	492.93
Net Slot Area (mm^2):	476.63
Limited Slot Fill Factor (%):	75
Stator Slot Fill Factor (%):	72.3342
Coil Half-Turn Length (mm):  	244.619
Wire Resistivity (ohm.mm^2/m):	0.0217


     ROTOR DATA

Minimum Air Gap (mm):  	1.6
Inner Diameter (mm):  	241.1
Length of Rotor (mm):  	125.7
Stacking Factor of Iron Core:	0.95
Type of Steel:	M800-50A
Polar Arc Radius (mm):  	160
Mechanical Pole Embrace:	0.7
Electrical Pole Embrace:	0.699991
Max. Thickness of Magnet (mm):  	6
Width of Magnet (mm):  	86.3153
Type of Magnet:	NdFe30_kniha
Type of Rotor:	1
Magnetic Shaft:	Yes


     PERMANENT MAGNET DATA

Residual Flux Density (Tesla):	1.05005
Coercive Force (kA/m):	800
Maximum Energy Density (kJ/m^3):	210.009
Relative Recoil Permeability:	1.04453
Demagnetized Flux Density (Tesla):	0
Recoil Residual Flux Density (Tesla):	1.05005
Recoil Coercive Force (kA/m):	800

     MATERIAL CONSUMPTION

Armature Wire Density (kg/m^3):  	8900
Permanent Magnet Density (kg/m^3):  	7550
Armature Core Steel Density (kg/m^3):  	7800
Rotor Core Steel Density (kg/m^3):  	7800

Armature Copper Weight (kg):  	27.4961
Permanent Magnet Weight (kg):  	3.93198
Armature Core Steel Weight (kg):  	66.1149
Rotor Core Steel Weight (kg):  	26.8733
Total Net Weight (kg):  	124.416

Armature Core Steel Consumption (kg):  	141.439
Rotor Core Steel Consumption (kg):  	70.7561


     STEADY STATE PARAMETERS

Stator Winding Factor:	0.683013
D-Axis Reactive Reactance Xad (ohm):	2.4587
Q-Axis Reactive Reactance Xaq (ohm):	2.4587
D-Axis Reactance X1+Xad (ohm):	3.26581
Q-Axis Reactance X1+Xaq (ohm):	3.26581
Armature Leakage Reactance X1 (ohm):	0.807106
Zero-Sequence Reactance X0 (ohm):	0.807106
Armature Phase Resistance R1 (ohm):	0.063267
Armature Phase Resistance at 20C (ohm):	0.0520422


     NO-LOAD MAGNETIC DATA

Stator-Teeth Flux Density (Tesla):	1.63909
Stator-Yoke Flux Density (Tesla):	1.01989
Rotor-Yoke Flux Density (Tesla):	1.09002
Air-Gap Flux Density (Tesla):	0.760401
Magnet Flux Density (Tesla):	0.802596

Stator-Teeth By-Pass Factor:	0.00209908
Stator-Yoke By-Pass Factor:	1.38053e-005
Rotor-Yoke By-Pass Factor:	1.37086e-005

Stator-Teeth Ampere Turns (A.T):	82.8084
Stator-Yoke Ampere Turns (A.T):	13.9556
Rotor-Yoke Ampere Turns (A.T):	9.33749
Air-Gap Ampere Turns (A.T):	1025.11
Magnet Ampere Turns (A.T):	-1131.15

Leakage-Flux Factor:	1
Correction Factor for Magnetic
  Circuit Length of Stator Yoke:	0.76667
Correction Factor for Magnetic
  Circuit Length of Rotor Yoke:	0.76667

No-Load Line Current (A):	34.1424
No-Load Input Power (W):	3179.51
Cogging Torque (N.m):	10.6268


     FULL-LOAD DATA

Maximum Line Induced Voltage (V):	1324.99
Root-Mean-Square Line Current (A):	145.307
Root-Mean-Square Phase Current (A):	145.307
Armature Thermal Load (A^2/mm^3):	743.515
Specific Electric Loading (A/mm):	96.1668
Armature Current Density (A/mm^2):	7.73151
Frictional and Windage Loss (W):	1615.2
Iron-Core Loss (W):	1340.95
Armature Copper Loss (W):	4007.39
Total Loss (W):	6963.53
Output Power (W):	160034
Input Power (W):	166997
Efficiency (%):	95.8302

Synchronous Speed (rpm):	2500
Rated Torque (N.m):	611.284
Torque Angle (degree):	60.5406

Maximum Output Power (W):	182639
Torque Constant KT (Nm/A):	2.43543


     WINDING ARRANGEMENT

The 3-phase, 2-layer winding can be arranged in 6 slots as below:

AAZZBB


Angle per slot (elec. degrees):	30
Phase-A axis (elec. degrees):	60
First slot center (elec. degrees):	0



     TRANSIENT FEA INPUT DATA 

For Armature Winding:
  Number of Turns:	224
  Parallel Branches:	2
  Terminal Resistance (ohm):	0.063267
  End Leakage Inductance (H):	0.000134041
2D Equivalent Value:
  Equivalent Model Depth (mm):	125.7
  Equivalent Stator Stacking Factor:	0.95
  Equivalent Rotor Stacking Factor:	0.95
  Equivalent Br (Tesla):	1.05005
  Equivalent Hc (kA/m):	800
Estimated Rotor Inertial Moment (kg m^2):	1.00932
